EXTRACTED TEXT FROM: 36颗调焦染色灯英文 JS.doc



LED36 head-stained lights


operating instruction

 




  




                











Menu operation
 
Menu structure
Main interface- - - -setting- - - -operation mode (DMX / self-travel / random / voice control)
----DMX Address (1-512)
----Channel mode (15 CH)
----X Reverse (on / off)
----Y Reverse (on / off)
----XY Encoder (on / off)
----No DMX signal (on / off)
----Screen saver (on / off)
----Restore the default settings

--hand movement

- -System- -Software version
		- -DMX channel value monitoring
- -System error record

- -Advanced- - -sensor monitoring
		- -Resignation calibration
- -Pattern color zero-point correction
 
 



- -Switching between Chinese and English
- -Screen rotation


set up
optionexplainrunning modeDMXMachine status: receiving DMX signal from the automatic control table or hostGo at a slow paceRandom walksound controlDMX address1~512Press OK to enter the edit state. At this time, select the hundred digits, press "up" and "down" key to change the address code. Press OK again to select the ten editors. Press OK again to select the single bit edit. Press to exit the edit status againchannel patternStandard 15CHStandard, 15-channel modeX reversalcloseopenY reversalcloseopenXY exchangecloseopenChannel channel for XY axis (including fine tuning)XY encoderopenUse the encoder (optocoupler) to judge the lost step and automatically correct the positioncloseDo not correct the position by using the encoder (optical coupling)There was no DMX signal
keepContinue running in the original statezero clearingMotor back, stop operationScreen protectionopenTurn off the backlight after 30 seconds of idlecloseBack light forever brightRestore default settingsPress OK to see the confirmation dialog box, and press OK again to restore the default settings

manual control

This interface is used to control the current lamps.
Press OK to enter the edit state. When hundreds are selected, press up and Down to change the channel value. Press OK again to select the ten editors. Press OK again to select the single bit edit. Press to exit the edit status again.

system info

optionexplainsoftware releaseCurrent software versionDMX channel valuesThis enters the subinterface and displays the channel values by value and percentage for viewingSystem error recordIf the red ERR indicator shines, the lamp is running wrong, and details can be viewed in the subinterface. After viewing, you can press the Clear " key to clear the error record
Note: Sometimes it is not really a hall or optical coupling installation problem, but the motor wiring in reverse
error messageexplainMotor reset failure, serial port errorThe drive board did not respond. There is a problem with the serial port communication line connecting the display board and the drive board, or with the drive board.X axis reduction failedX-axis photoelectric switch, or X-axis motor problemThe reduction of the Y axis failedY-axis photoelectric switch, or Y-axis motor problemX-axis Hall error"The X-axis Hall has a problemY-axis Hall errorThe Y-axis Hall has a problemThe color disk reset failedColor disc Hall, or color disc motor problemsPattern disk reset failedPattern disk Hall, or pattern disk motor problemsThe focus reset failedFocus Hall, or focus motor problemsBulb control failedBright bubble or bubble failure, the lamp or bulb problem
senior

Here to set a layer of password to prevent non-professionals from misoperation. The default password is Up Up Down Down. Press OK to verify the password.
optionexplainReset calibrationAfter entering the sub-interface, the reset position of the X-axis and Y-axis motors can be adjusted to make up for the error in the hardware installation. The adjustment range is-128~ + 127, and + 0 means that there is no adjustment.Sensor monitoringReal-time monitoring of various photoelectric switches, hall and other sensors
channel pattern:
channel161X-axis (horizontal)000-2552Y-axis (vertical)000-2553XY velocity000-2554Total dimming000-2555Red (R), Group 1000-2556Green (G) Group 1000-2557Blue (B), Group 1000-2558White (W) Group 1000-2559stroboflash000-25510focus000-25511functioning pattern000-25512Functional mode speed000-25513X axis fine-tuning000-25514Y axis fine-tuning000-25515resetThe value of 000-249 is invalid
250 – 255 were reset16No obligate0
